Inductive Sensor Pepperl+Fuchs NRB20-U1-E2-IO
Pepperl+Fuchs Categories
Contact via Zalo
Phone call
Datasheet excerpt: Technical data of NRB20-U1-E2-IO
| Overall specifications | ||
|---|---|---|
| transition function | Programmable normally open/closed (NO/NC) | |
| Output configuration | PNP | |
| Specified functioning distance | 20 mm (factory default) | |
| Proximity functioning range | 15 mm (activation possible through software) | |
| mounting | flush | |
| Output configuration | DC | |
| Guaranteed functioning distance | 0 ... 16.2 mm | |
| diminution factor rAl | 1 | |
| diminution factor rCu | 1 | |
| diminution factor r304 | 1 | |
| diminution factor rSt37 | 1 | |
| Output configuration | 3-wire | |
| Rated specifications | ||
| Operational voltage | 10 ... 30 V DC | |
| commutation frequency | 0 ... 440 Hz (switch point mode) 0 ... 10 Hz (window mode, switching point mode with stability alert) |
|
| Deadband | typ. 3 % | |
| Polarity reversal protection | reverse polarity safeguarded | |
| Overcurrent protection | pulsing | |
| voltage loss | = 0.5 V | |
| Operational current | 0 ... 200 mA | |
| Non-conducting current | 0 ... 0.5 mA typ. 60 µA at 25 °C | |
| No-load input current | = 20 mA | |
| Delay time prior to availability | max. 150 ms | |
| Uniform magnetic field | 200 mT | |
| Oscillating magnetic field | 200 mT | |
| Voltage functioning indicator | LED, green | |
| Condition indicator | LED, yellow | |
| Parameters related to functional safety | ||
| MTTFd | 701 a | |
| task duration (TM) | 20 a | |
| Diagnostic Range (DC) | 0 % | |
| Connection point | ||
| Type of interface | IO-Link ( via C/Q = terminal 4 ) | |
| IO-Link revision | 1.1 | |
| Device ID | 0x201005 (2101253) | |
| data transfer rate | COM2 (38.4 kBit/s) | |
| Minimum cycle time | 2.3 ms | |
| process data range | procedural information entry (control system aspect): 2 Bit procedural information output (control system side): not applicable |
|
| SIO mode support | yes | |
| Compatible master port classification | A | |
| Adherence to standards and directives | ||
| Compliance with standards | ||
| Standards | EN IEC 60947-5-2 | |
| Certifications and approvals | ||
| Ingress protection rating | II | |
| Nominal insulation voltage | 60 V | |
| Rated surge voltage withstand capability | 800 V | |
| UL certification | cULus Certified, Standard Use Class 2 power supply |
|
| CCC certification | CCC certification / marking not necessary for products rated ≤36 V | |
| Environmental conditions | ||
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) | |
| Ambient storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Mechanical characteristics | ||
| Linkage method | screw terminals | |
| Linkage information | Up to two conductors with identical core cross-section may be connected to a single terminal connection! torque specification 1.2 Nm + 10 % |
|
| cross section of the core | up to 2.5 mm2 | |
| Minimum conductor cross-section | without cable end sleeves 0.5 mm2 , incorporating connector sleeves 0.34 mm2 | |
| Maximum core cross-section area | without cable end sleeves 2.5 mm2 , featuring connector sleeves 1.5 mm2 | |
| Housing material | PA/metal featuring epoxy powder finish | |
| detection surface | PA | |
| enclosure base | plastic | |
| Protection等级 | IP67 | |
| Mass | 275 g | |
| Measurements | ||
| Height | 40 mm | |
| Width | 40 mm | |
| Length | 118 mm | |
| Note | tightening torque: 1.8 Nm (enclosure) | |
| Default configurations | ||
| Factory configuration | functioning mode = switching point mode with stability alert switching function = normally open (NO) activation distance = 20 mm |
|
Classifications
| Configuration | Classification code |
|---|---|
| ECLASS 13.0 | 27274001 |
| ECLASS 12.0 | 27274001 |
| ECLASS 11.0 | 27270101 |
| ECLASS 10.0.1 | 27270101 |
| ECLASS 9.0 | 27270101 |
| ECLASS 8.0 | 27270101 |
| ECLASS 5.1 | 27270101 |
| ETIM 9.0 | EC002714 |
| ETIM 8.0 | EC002714 |
| ETIM 7.0 | EC002714 |
| ETIM 6.0 | EC002714 |
| ETIM 5.0 | EC002714 |
| UNSPSC 12.1 | 39121550 |
Download Specification for NRB20-U1-E2-IO
Download PDFRELATED PRODUCTS
Inductive Sensor NMB6-F104M-E2-FE-200MM-V1
- Brand: PEPPERL+FUCHS
-
Category:
Inductive Sensor -
Product Code:
Inductive Sensor NBN40-L2-E2-220MM-3DT04
- Brand: PEPPERL+FUCHS
-
Category:
Inductive Sensor -
Product Code: