Photoelectric Sensor Pepperl+Fuchs OBE20M-R102-S2EP-IO-V31-L

Pepperl+Fuchs Categories

Photoelectric Sensor OBE20M-R102-S2EP-IO-V31-L

Brand: Pepperl+Fuchs
Product Code:

Contact via Zalo

Phone call

Share on:

Description Download Accessories

Datasheet excerpt: Technical data of OBE20M-R102-S2EP-IO-V31-L

System elements
Emitter		OBE20M-R102-S-IO-V31-L
Receiver		OBE20M-R102-2EP-IO-V31-L
Overall specifications
Operational sensing range		0 ... 20 m
detection range threshold		30 m
illumination source		laser diode
Illumination type		modulated red light in the visible spectrum
Laser specified ratings
	Note	LASER LIGHT , DO NOT STARE INTO BEAM
	Laser category	1
	Wavelength	680 nm
	Beam spreading	> 5 mrad; d63 < 2 mm within the range of 250 mm ... 750 mm
	pulse duration	1.6 µs
	Repetition frequency	max. 17.6 kHz
	maximum pulse energy	9.6 nJ
Size of the illumination spot		approximately 50 mm at a separation of 20 m
angle of opening		approx. 0.3 °
Ambient light threshold		EN 60947-5-2 : 30000 Lux
Parameters related to functional safety
MTTF_d		440 a
task duration (T_M)		20 a
Diagnostic Range (DC)		0 %
Indicators/operation controls
Operational status indicator		LED green: always active - power on flashing (4Hz) - short circuit condition flashing with brief interruption (1 Hz) - IO-Link mode
operation indicator		Yellow LED: Constantly illuminated - unobstructed light path Permanently off - entity detected Flashing (4 Hz) - inadequate operational reserve
control components		Transducer: light/dark switch
control components		Transducer: sensitivity configuration
Parameterization signal		IO-Link communication: green LED turns off momentarily (1 Hz)
Electrical parameters
Operational voltage		10 ... 30 V DC
Ripple		max. 10 %
No-load input current		Emitter: = 13 mA Transducer: = 13 mA with 24 V supply voltage
Ingress protection rating		III
Connection point
Type of interface		IO-Link ( via C/Q = pin 4 )
IO-Link revision		1.1
Device ID		Emitter: 0x110406 (1115142) Transducer: 0x110306 (1114886)
data transfer rate		COM2 (38.4 kBit/s)
Minimum cycle time		2.3 ms
process data range		Emitter: procedural information transmission: 2 Bit Transducer: procedural information entry: 2 Bit procedural information transmission: 2 Bit
SIO mode support		yes
Compatible master port classification		A
Input
Verification input		emitter shutdown at +U_B
Output
Type of switch		The sensor features an adjustable switching type. The factory default setting is: C/Q - Pin4: NPN default open / dark-on, PNP default closed / light-on, IO-Link /Q - Pin2: NPN configuration normally closed / light-activated, PNP configuration normally open / dark-activated
Output signal		2 push-pull (4 in 1) outputs, equipped with short-circuit protection, reverse polarity protection, and overvoltage protection
Switching voltage level		max. 30 V DC
Switching capacity		max. 100 mA, resistive load
Usage category		DC-12 and DC-13
voltage loss		= 1.5 V DC
commutation frequency		1250 Hz
reaction time		0.4 ms
Compliance
Communication interface		IEC 61131-9
Product specification		EN 60947-5-2
Laser safety		EN 60825-1:2014
Certifications and approvals
UL certification		E87056, cULus Certified, Class 2 power supply, type rating 1
FDA certification		IEC 60825-1:2007 conforms with 21 CFR 1040.10 and 1040.11, excluding deviations as stated in Laser Notice No. 50, dated June 24, 2007
Environmental conditions
Ambient temperature		-40 ... 60 °C (-40 ... 140 °F)
Ambient storage temperature		-40 ... 70 °C (-40 ... 158 °F)
Mechanical characteristics
Protection等级		IP67 / IP69 / IP69K
Linkage		M8 x 1 socket, 4-pin
Material
	Housing	PC (PC (polycarbonate))
	optical surface	Annealed glass
Mass		Emitter: approx. 10 g receiver: approx. 10 g
Measurements
	Height	33.8 mm
	Width	13.9 mm
	Depth	18.3 mm

Classifications

Configuration	Classification code
ECLASS 13.0	27270901
ECLASS 12.0	27270901
ECLASS 11.0	27270901
ECLASS 10.0.1	27270901
ECLASS 9.0	27270901
ECLASS 8.0	27270901
ECLASS 5.1	27270901
ETIM 9.0	EC002716
ETIM 8.0	EC002716
ETIM 7.0	EC002716
ETIM 6.0	EC002716
ETIM 5.0	EC002716
UNSPSC 12.1	39121528