Photoelectric Sensor Pepperl+Fuchs OBE40M-R201-S2EP-IO-V1-L


Pepperl+Fuchs Categories

Photoelectric Sensor Pepperl+Fuchs obe40m-r201-s2ep-io-v1-l

Photoelectric Sensor OBE40M-R201-S2EP-IO-V1-L

Brand: Pepperl+Fuchs
Product Code:

Share on:

Datasheet excerpt: Technical data of  OBE40M-R201-S2EP-IO-V1-L

Classifications

Item Specification
Laser thru-beam sensor
System elements
EmitterOBE40M-R201-S-IO-V1-L
ReceiverOBE40M-R201-2EP-IO-V1-L
Overall specifications
Operational sensing range0 ... 40 m
detection range threshold50 m
illumination sourcelaser diode
Illumination typemodulated red light in the visible spectrum
Laser specified ratings
NoteLASER LIGHT , DO NOT STARE INTO BEAM
Laser category1
Wavelength680 nm
Beam spreading> 5 mrad; d63 < 2 mm within the range of 250 mm ... 750 mm
pulse duration1.6 µs
Repetition frequencymax. 17.6 kHz
maximum pulse energy9.6 nJ
Alignment toolRed LED (within receiver lens)
constantly illuminated: beam is interrupted,
flashes: achieving switching threshold,
off: adequate operational margin
Size of the illumination spotapproximately 80 mm at a separation of 40 m
angle of openingapprox. 0.12 °
Ambient light thresholdEN 60947-5-2 : 40000 Lux
Parameters related to functional safety
MTTFd440 a
task duration (TM)20 a
Diagnostic Range (DC)60 %
Indicators/operation controls
Operational status indicatorLED green:
always active - power on
flashing (4Hz) - short circuit condition
flashing with brief interruption (1 Hz) - IO-Link mode
operation indicatorYellow LED:
Constantly illuminated - unobstructed light path
Permanently off - entity detected
Flashing (4 Hz) - inadequate operational reserve
control componentsTransducer: light/dark switch
control componentsTransducer: sensitivity configuration
Electrical parameters
Operational voltage10 ... 30 V DC
Ripplemax. 10 %
No-load input currentEmitter: = 13 mA
Transducer: = 15 mA at 24 V supply voltage
Ingress protection ratingIII
Connection point
Type of interfaceIO-Link ( via C/Q = pin 4 )
IO-Link revision1.1
equipment profileRecognition and troubleshooting
intelligent sensor:
Transducer: type 2.4
Emitter: -
Device IDEmitter: 0x111412 (1119250)
Transducer: 0x111312 (1118994)
data transfer rateCOM2 (38.4 kBit/s)
Minimum cycle time2.3 ms
process data rangeEmitter:
procedural information entry: 0 bit
procedural information transmission: 1 bit
Transducer:
procedural information entry: 2 bit
procedural information transmission: 2 bit
SIO mode supportyes
Compatible master port classificationA
Input
Verification inputemitter shutdown at +UB
Output
Type of switchThe sensor features an adjustable switching type. The factory default setting is:
C/Q - Pin4: NPN default open / dark-on, PNP default closed / light-on, IO-Link
/Q - Pin2: NPN configuration normally closed / light-activated, PNP configuration normally open / dark-activated
Output signal2 push-pull (4 in 1) outputs, equipped with short-circuit protection, reverse polarity protection, and overvoltage protection
Switching voltage levelmax. 30 V DC
Switching capacitymax. 100 mA, resistive load
Usage categoryDC-12 and DC-13
voltage loss= 1.5 V DC
commutation frequency1250 Hz
reaction time0.4 ms
Compliance
Communication interfaceIEC 61131-9
Product specificationEN 60947-5-2
Laser safetyEN 60825-1:2014
Certifications and approvals
UL certificationE87056, cULus Certified, Class 2 power supply, type rating 1
CCC certificationCCC certification / marking not necessary for products rated ≤36 V
FDA certificationIEC 60825-1:2007 conforms with 21 CFR 1040.10 and 1040.11, excluding deviations as stated in Laser Notice No. 50, dated June 24, 2007
Environmental conditions
Ambient temperature-40 ... 60 °C (-40 ... 140 °F)
Ambient storage temperature-40 ... 70 °C (-40 ... 158 °F)
Mechanical characteristics
Protection等级IP67 / IP69 / IP69K
Linkage4-pin, M12 x 1 connector, 90° rotatable
Material
HousingPC (PC (polycarbonate))
optical surfacePMMA
MassEmitter: approx. 47 g receiver: approx. 47 g
Measurements
Height61.7 mm
Width15 mm
Depth41.7 mm

Download Specification for OBE40M-R201-S2EP-IO-V1-L

Download PDF
SensorActuatorCables V1-G-2M-PUR

  • Brand: Pepperl+Fuchs
  • Product Code:

SensorActuatorCables V1-W-2M-PUR

  • Brand: Pepperl+Fuchs
  • Product Code:

RELATED PRODUCTS