Photoelectric Sensor Pepperl+Fuchs OQT350-R201-2EP-IO-0,3M-V1-L

Pepperl+Fuchs Categories

Photoelectric Sensor OQT350-R201-2EP-IO-0,3M-V1-L

Brand: Pepperl+Fuchs
Product Code:

Contact via Zalo

Phone call

Share on:

Description Download Accessories

Datasheet excerpt: Technical data of OQT350-R201-2EP-IO-0,3M-V1-L

Classifications

Item Specification
Measuring sensor featuring multiple switching points

Overall specifications
Detection distance		60 ... 350 mm
Minimum detection range		60 ... 100 mm
Maximum detection range		40 ... 400 mm
modification range		100 ... 350 mm
Reference point		typical white, 100 mm x 100 mm
illumination source		laser diode
Illumination type		modulated red light in the visible spectrum
Laser specified ratings
	Note	LASER LIGHT , DO NOT STARE INTO BEAM
	Laser category	1
	Wavelength	680 nm
	Beam spreading	> 5 mrad, d63 < 2,8 mm in the range of 350 mm ... 800 mm
	pulse duration	5.5 µs
	Repetition frequency	approx. 2.4 kHz
	maximum pulse energy	< 40 nJ
Black-white contrast (6 %/90 %)		< 2 %
Size of the illumination spot		approximately 3 mm at a distance of 350 mm
angle of opening		approx. 0.3 °
Ambient light threshold		EN 60947-5-2 : 45000 Lux
Parameters related to functional safety
MTTF_d		560 a
task duration (T_M)		20 a
Diagnostic Range (DC)		0 %
Indicators/operation controls
Operational status indicator		LED green: always active - power on flashing (4Hz) - short circuit condition flashing with brief interruption (1 Hz) - IO-Link mode
operation indicator		Yellow indicator LED: permanently on - output switch is active permanently off - switch output not active
control components		learning key
control components		5-position rotary switch for selecting functioning modes
Electrical parameters
Operational voltage		10 ... 30 V DC
Ripple		max. 10 %
No-load input current		< 16 mA at 24 V supply voltage
Ingress protection rating		III
Connection point
Type of interface		IO-Link ( via C/Q = pin 4 )
IO-Link revision		1.1
equipment profile		Recognition and troubleshooting intelligent sensor type 0
Device ID		0x111812 (1120274)
data transfer rate		COM2 (38.4 kBit/s)
Minimum cycle time		2.3 ms
process data range		process data entry 2 Bit procedural information output 2 Bit
SIO mode support		yes
Compatible master port classification		A
Output
Type of switch		The factory configuration is: C/Q - Pin4: NPN normally open, PNP normally closed, IO-Link Q2 - Pin2: NPN open by default, PNP closed by default
Output signal		2 push-pull (4 in 1) outputs, equipped with short-circuit protection, reverse polarity protection, and overvoltage protection
Switching voltage level		max. 30 V DC
Switching capacity		max. 100 mA, resistive load
Usage category		DC-12 and DC-13
voltage loss		= 1.5 V DC
commutation frequency		217 Hz
reaction time		2.3 ms
Compliance
Communication interface		IEC 61131-9
Product specification		EN 60947-5-2
Laser safety		EN 60825-1:2014
Certifications and approvals
UL certification		E87056, cULus Certified, Class 2 power supply, type rating 1
CCC certification		CCC certification / marking not necessary for products rated ≤36 V
FDA certification		IEC 60825-1:2014 meets the requirements of 21 CFR 1040.10 and 1040.11, excluding deviations as outlined in Laser Notice No. 50, dated June 24, 2007
Environmental conditions
Ambient temperature		-40 ... 60 °C (-40 ... 140 °F), cable, stationary installation -20 ... 60 °C (-4 ... 140 °F), flexible cable unsuitable for use with conveyor chains
Ambient storage temperature		-40 ... 70 °C (-40 ... 158 °F)
Mechanical characteristics
Protection等级		IP67 / IP69 / IP69K
Linkage		300 mm stationary cable featuring an M12 x 1, 4-pin connector
Material
	Housing	PC (PC (polycarbonate))
	optical surface	PMMA
Mass		approx. 55 g
Measurements
	Height	61.7 mm
	Width	15 mm
	Depth	41.7 mm
Cable duration		0.3 m