Photoelectric Sensor Pepperl+Fuchs OBE12M-R100-SE5F-IO-V31

Pepperl+Fuchs Categories

Photoelectric Sensor OBE12M-R100-SE5F-IO-V31

Brand: Pepperl+Fuchs
Product Code:

Contact via Zalo

Phone call

Share on:

Description Download Accessories

Datasheet excerpt: Technical data of OBE12M-R100-SE5F-IO-V31

System elements
Emitter		OBE12M-R100-S-IO-V31
Receiver		OBE12M-R100-E5F-IO-V31
Overall specifications
Operational sensing range		0 ... 12 m
detection range threshold		15 m
illumination source		LED
Illumination type		modulated red light in the visible spectrum
LED risk category labeling		exemption category
Size of the illumination spot		approximately 65 mm at a range of 1 m
angle of opening		3.7 °
Ambient light threshold		EN 60947-5-2 : 30000 Lux
Parameters related to functional safety
MTTF_d		462 a
task duration (T_M)		20 a
Diagnostic Range (DC)		0 %
Indicators/operation controls
Operational status indicator		LED green: always active - power on flashing (4Hz) - short circuit condition flashing with brief interruption (1 Hz) - IO-Link mode
operation indicator		Yellow LED: Constantly illuminated - unobstructed light path Permanently off - entity detected Flashing (4 Hz) - inadequate operational reserve
control components		Transducer: light/dark switch
control components		Transducer: sensitivity configuration
Parameterization signal		IO-Link communication: green LED turns off momentarily (1 Hz)
Electrical parameters
Operational voltage		10 ... 30 V DC
Ripple		max. 10 %
No-load input current		Emitter: = 14 mA Transducer: = 13 mA with 24 V supply voltage
Ingress protection rating		III
Connection point
Type of interface		IO-Link ( via C/Q = pin 4 )
IO-Link revision		1.1
Device ID		Emitter: 0x110401 (1115137) Transducer: 0x11030B (1114891)
data transfer rate		COM2 (38.4 kBit/s)
Minimum cycle time		2.3 ms
process data range		Emitter: procedural information transmission: 2 Bit Transducer: procedural information entry: 2 Bit procedural information transmission: 2 Bit
SIO mode support		yes
Compatible master port classification		A
Input
Verification input		emitter shutdown at +U_B
Output
Stability fault indication output		1 PNP, disabled when the level drops below the functioning reserve after approximately 5 s Automatically disabled if the beam is broken 4 times during the flash duration
Type of switch		The sensor features an adjustable switching type. The factory default setting is: C/Q - Pin4: PNP normally open / dark-activated, IO-Link Alarm output - Pin2: PNP normally closed
Output signal		1 PNP, safeguarded against short circuits, protected from reverse polarity
Switching voltage level		max. 30 V DC
Switching capacity		max. 100 mA, resistive load
Usage category		DC-12 and DC-13
voltage loss		= 1.5 V DC
commutation frequency		1000 Hz
reaction time		0.5 ms
Compliance
Communication interface		IEC 61131-9
Product specification		EN 60947-5-2
Certifications and approvals
UL certification		E87056, cULus Certified, Class 2 power supply, type rating 1
Environmental conditions
Ambient temperature		-40 ... 60 °C (-40 ... 140 °F)
Ambient storage temperature		-40 ... 70 °C (-40 ... 158 °F)
Mechanical characteristics
Protection等级		IP67 / IP69 / IP69K
Linkage		M8 x 1 socket, 4-pin
Material
	Housing	PC (PC (polycarbonate))
	optical surface	PMMA
Mass		Emitter: approx. 10 g receiver: approx. 10 g
Measurements
	Height	44.5 mm
	Width	11 mm
	Depth	21.5 mm

Classifications

Configuration	Classification code
ECLASS 13.0	27270901
ECLASS 12.0	27270901
ECLASS 11.0	27270901
ECLASS 10.0.1	27270901
ECLASS 9.0	27270901
ECLASS 8.0	27270901
ECLASS 5.1	27270901
ETIM 9.0	EC002716
ETIM 8.0	EC002716
ETIM 7.0	EC002716
ETIM 6.0	EC002716
ETIM 5.0	EC002716
UNSPSC 12.1	39121528