Photoelectric Sensor Pepperl+Fuchs OBE25M-R200-SEP-IO-V3

Pepperl+Fuchs Categories

Photoelectric Sensor OBE25M-R200-SEP-IO-V3

Brand: Pepperl+Fuchs
Product Code:

Contact via Zalo

Phone call

Share on:

Description Download Accessories

Datasheet excerpt: Technical data of OBE25M-R200-SEP-IO-V3

Classifications

Item Specification
Through-beam sensor KIT

System elements
Emitter		OBE25M-R200-S-IO-V3
Receiver		OBE25M-R200-EP-IO-V3
Overall specifications
Operational sensing range		0 ... 25 m
detection range threshold		33 m
illumination source		LED
Illumination type		modulated red light in the visible spectrum
LED risk category labeling		exemption category
Alignment tool		Red LED (within receiver lens) constantly illuminated: beam is interrupted, flashes: achieving switching threshold, off: adequate operational margin
Size of the illumination spot		approximately 850 mm at a distance of 25 m
angle of opening		approx. 2 °
Ambient light threshold		EN 60947-5-2 : 40000 Lux
Parameters related to functional safety
MTTF_d		462 a
task duration (T_M)		20 a
Diagnostic Range (DC)		60 %
Indicators/operation controls
Operational status indicator		LED green: always active - power on flashing (4Hz) - short circuit condition flashing with brief interruption (1 Hz) - IO-Link mode
operation indicator		Yellow LED: Constantly illuminated - unobstructed light path Permanently off - entity detected Flashing (4 Hz) - inadequate operational reserve
control components		Transducer: light/dark switch
control components		Transducer: sensitivity configuration
Electrical parameters
Operational voltage		10 ... 30 V DC
Ripple		max. 10 %
No-load input current		Emitter: = 15 mA Transducer: = 15 mA at 24 V supply voltage
Ingress protection rating		III
Connection point
Type of interface		IO-Link ( via C/Q = pin 4 )
IO-Link revision		1.1
equipment profile		Recognition and troubleshooting intelligent sensor: Transducer: type 2.4 Emitter: -
Device ID		Emitter: 0x111401 (1119233) Transducer: 0x111301 (1118977)
data transfer rate		COM2 (38.4 kBit/s)
Minimum cycle time		2.3 ms
process data range		Emitter: procedural information entry: 0 bit procedural information transmission: 1 bit Transducer: procedural information entry: 2 bit procedural information transmission: 2 bit
SIO mode support		yes
Compatible master port classification		A
Input
Verification input		emitter shutdown at +U_B
Output
Type of switch		The sensor features an adjustable switching type. The factory default setting is: C/Q - Pin4: NPN default open / dark-on, PNP default closed / light-on, IO-Link
Output signal		1 push-pull (4 in 1) output, short-circuit protection, reverse polarity protection, overvoltage protection
Switching voltage level		max. 30 V DC
Switching capacity		max. 100 mA, resistive load
Usage category		DC-12 and DC-13
voltage loss		= 1.5 V DC
commutation frequency		1000 Hz
reaction time		0.5 ms
Compliance
Communication interface		IEC 61131-9
Product specification		EN 60947-5-2
Certifications and approvals
EAC compliance		TR CU 020/2011
UL certification		E87056, cULus Certified, Class 2 power supply, type rating 1
CCC certification		CCC certification / marking not necessary for products rated ≤36 V
Environmental conditions
Ambient temperature		-40 ... 60 °C (-40 ... 140 °F)
Ambient storage temperature		-40 ... 70 °C (-40 ... 158 °F)
Mechanical characteristics
Protection等级		IP67 / IP69 / IP69K
Linkage		plug connector, M8 x 1, 3-pin, adjustable by 90°
Material
	Housing	PC (PC (polycarbonate))
	optical surface	PMMA
Mass		Emitter: approx. 35 g receiver: approx. 35 g
Measurements
	Height	50.6 mm
	Width	15 mm
	Depth	41.7 mm